Crusader MP 5.0L Manual de Serviço

EngineEngine Model:General Motors 5.0 L PowertrainGeneral Motors 5.7 L PowertrainGenerator Models:50 kW (5.0 L)50/60 kW (5.7 L)TP-6104 11/01aService

Fastener Tightening Specifications (cont’d)ApplicationSpecificationMetric EnglishEngine Block Coolant Drain Hole Plug 20 N·m 15 lb ftEngine Block Oil Ga

Notice:SIO-ID = 5005 The Linear EGR valve is anelectrical component. DO NOT soak in any liquidcleaner or solvent because damage may result.10. Remove

14. Remove the manifold absolute pressure (MAP)sensor from the upper intake manifold.15. Remove the MAP sensor seal from the MAPsensor.16. Discard the

26. Remove the upper intake manifold studs (1).27. Remove the upper intake manifold (2).28. Remove the upper intake manifold to lower intakemanifold g

3. Clean the lower intake manifold in cleaningsolvent.4. Dry the lower intake manifold with compressed air.5. Inspect the upper intake manifold for th

Intake Manifold AssembleSIE-ID = 1945131. Install the fuel meter body (5) into the lower intakemanifold (6).2. Install the 8 poppet nozzles into the l

12. Install the NEW fuel seals (8), black O-rings, intothe fuel meter body.13. Install the NEW spacer rings (7), flat washers, intothe fuel meter body.

23. Install the ignition coil and studs.TightenTighten the ignition coil studs to12 N·m (106 lb in).24. If reusing the engine coolant temperature (ECT

27. Install the EGR valve bolts.Tighten27.1. Tighten the EGR valve bolts on thefirst pass to 10 N·m (88 lb in).27.2. Tighten the EGR valve bolts on the

35. Install the accelerator control bracket, the bolt,and the nut.TightenTighten the accelerator control bracket bolt andthe nut to 12 N·m (106 lb in)

Water Pump Cleaning and InspectionSIE-ID = 194965Caution: Refer to Safety Glasses Caution inCautions and Notices.1. Remove the old gasket material fro

Fastener Tightening Specifications (cont’d)ApplicationSpecificationMetric EnglishSpark PlugInitial Installation – NEW Cylinder Head 30 N·m 22 lb ftAll S

8. Screw the thread insert onto the mandrel of thethread insert installer. Engage the tang of thethread insert onto the end of the mandrel.Important:

Service Prior to AssemblySIE-ID = 43122• Dirt will cause premature wear of the rebuiltengine. Clean all the components.• Use the proper tools to measu

Engine Block Plug InstallationSIE-ID = 348917Tools RequiredJ 41712Oil Pressure Switch SocketCaution: Refer to Safety Glasses Caution inCautions and No

5. Apply sealant GM P/N United States 12346004,GM P/N Canada 10953480, or equivalent, to thethreads of the left side rear and left rear topengine oil

11. Apply threadlock GM P/N United States 12345382,GM P/N Canada 10953489, or equivalent, to theoutside diameter of the NEW engine blockcore hole plug

18. Apply sealant GM P/N United States 12346004,GM P/N Canada 10953480, or equivalent, to thethreads of the engine oil pressure gage sensor.19. Instal

3. Apply clean engine oil to the crankshaft bearingjournals.4. Install the crankshaft.5. Install the crankshaft bearings into the crankshaftbearing ca

11. Ensure that the crankshaft bearing caps are fullyseated in the engine block crankshaft bearing capchannel, and that the crankshaft bearing capsare

Crankshaft Rear Oil Seal and HousingInstallationSIE-ID = 348923Tools RequiredJ 35621-BRear Main Seal InstallerNotice:Refer toFastener Noticein Caution

11. Apply a small amount, approximately 2–3 drops,of clean engine oil GM P/N UnitedStates 12345610, GM P/N Canada 993193, orequivalent, to the outside

Engine Mechanical Specifications (5.0 L) (cont’d)ApplicationSpecificationMetric EnglishCrankshaftCrankshaft Bearing Clearance – Journal #1 – Production

3. Install theJ 8037onto the piston and compressthe piston rings.Important: The mark on the top of the piston mustface the front of the engine block.W

7. Remove theJ 5239from the connecting rod bolts.Notice:Refer toFastener Noticein Cautions andNotices.8. Install the connecting rod bearing, cap, and

Camshaft InstallationSIE-ID = 66855Notice:SIO-ID = 13833 All camshaft journals are thesame diameter, so care must be used in removingor installing the

Timing Chain and Sprockets InstallationSIE-ID = 69464Tools RequiredJ 5590Installer1. Install the crankshaft balancer woodruff keys intothe crankshaft

Notice:SIO-ID = 788777 Do not use tools to force thecamshaft sprocket onto the camshaft. The camshaftsprocket is a slip fit onto the camshaft and doesn

Engine Front Cover InstallationSIE-ID = 194773Notice:Refer toFastener Noticein Cautions andNotices.Important: Do not reuse the composite type enginefr

Oil Pump, Pump Screen and DeflectorInstallationSIE-ID = 194869Tools RequiredJ 36660-ATorque Angle Meter1. Inspect for properly installed oil pump locat

Oil Pan InstallationSIE-ID = 66859Notice:Refer toFastener Noticein Cautions andNotices.1. Install the oil pan studs into the engine block.TightenTight

Important: Always install a NEW oil pan gasket.The oil pan gasket and oil pan must be installed andthe fasteners tightened while the adhesive is still

Oil Filter Adapter InstallationSIE-ID = 695081. Apply clean engine oil GM P/N UnitedStates 12345610, GM P/N Canada 993193, orequivalent, to the NEW oi

Engine Mechanical Specifications (5.0 L) (cont’d)ApplicationSpecificationMetric EnglishPiston Compression Ring Groove Clearance – Service Limit – TopGro

Notice:Refer toFastener Noticein Cautions andNotices.5. Use theJ 23523-Fin order to press the crankshaftbalancer onto the crankshaft.5.1. Install theJ

9. Install the crankshaft balancer washer andthe bolt.TightenTighten the crankshaft balancer bolt to95 N·m (70 lb ft).Valve Lifter InstallationSIE-ID

Cylinder Head Installation - LeftSIE-ID = 650067Tools RequiredJ 36660-ATorque Angle Meter1. Clean the cylinder gasket surfaces on theengine block.2. I

6. Apply sealant GM P/N United States 12346004,GM P/N Canada 10953480, or equivalent, to thethreads of the cylinder head bolts.Notice:Refer toFastener

11. If reusing the engine coolant temperature (ECT)gage sensor, apply sealant GM P/N UnitedStates 12346004, GM P/N Canada 10953480 tothe threads of th

5. Install the cylinder head to the engine block.Guide the cylinder head carefully into place overthe dowel pins and the head gasket.6. Apply sealant

9. Measure the NEW spark plugs for the proper gap.Adjust the spark plug gap, if necessary.SpecificationsSpark plug gap to 1.52 mm (0.060 in).10. Instal

Valve Lash AdjustmentSIE-ID = 1947341. Turn the valve rocker arm nuts clockwise until allof the valve lash is removed.2. Turn the crankshaft clockwise

6. With the engine in the number 6 firing position,adjust the exhaust valves for cylindersnumber 2, 5, 6, and 7 and the intake valves forcylinders numb

Notice:SIO-ID = 41431 Apply the proper amount of thesealant when assembling this component. Excessiveuse of the sealant can prohibit the componentfrom

Engine Mechanical Specifications (5.7 L) (cont’d)ApplicationSpecificationMetric EnglishCamshaftEnd Play 0.05–0.30 mm 0.002–0.012 inJournal Diameter 47.4

Notice:SIO-ID = 382467 Proper lower intake manifoldfastener tightening sequence and torque is critical.Always follow the tightening sequence, and torq

2. Remove the distributor cap bolts and discard.3. Remove the distributor cap.4. Install a NEW distributor gasket onto thedistributor.5. Align the ind

7. Align the slotted tang in the oil pump driveshaftwith the distributor driveshaft. Rotate the oil pumpdriveshaft with a screwdriver if necessary.8.

13. Install the distributor cap onto the distributor.14. Install the NEW distributor cap bolts.Do not overtighten the NEW distributor cap bolts.Tighte

Valve Rocker Arm CoverInstallation - RightSIE-ID = 650070Important: Always install a NEW valve rocker armcover gasket.1. Install the NEW valve rocker

6. Install the fan and water pump pulley and boltsusing theJ 41240.TightenTighten the fan and water pump pulley bolts to25 N·m (18 lb ft).Oil Level In

6. Install the spark plug wire supports and bolts.TightenTighten the bolts to 12 N·m (106 lb in).7. Install the spark plug wires onto the spark plugs.

Engine Flywheel InstallationSIE-ID = 7842411. Install the engine flywheel (1 or 2) to thecrankshaft.Align the engine flywheel locator hole to theflywheel

Description and OperationEngine Component DescriptionSIE-ID = 69042Cylinder BlockThe engine block is made of cast iron and haseight cylinders arranged

5.0L and 5.7L engines have two bolts per crankshaftbearing cap. The heavy duty 5.7L engines havefour bolts per crankshaft bearing cap, on bearing caps

Engine Mechanical Specifications (5.7 L) (cont’d)ApplicationSpecificationMetric EnglishPiston Bore Clearance – Production 0.018–0.053 mm 0.0007–0.002 in

Lubrication DescriptionSIE-ID = 650073The gear-type oil pump is driven through an extensiondriveshaft. The extension driveshaft is driven by thedistri

Cleanliness and CareSIE-ID = 19007• Throughout this section, it should be understoodthat proper cleaning and protection of machinedsurfaces and fricti

− Abrasive pads also produce a fine grit thatthe oil filter cannot remove from theengine oil.This fine grit is an abrasive and can causeinternal engine d

• Do not overtighten the fasteners.− Apply the gasket eliminator sealant evenly toget a uniform thickness of the gasketeliminator sealant on the seali

Special Tools and EquipmentSIE-ID = 690690Illustration Tool Number/ Description14487J 3049-AValve Lifter Remover3404J 5239Connecting Rod BoltGuide Set

Illustration Tool Number/ Description2014J 8001Dial Indicator Set3403J 8037Ring Compressor3414J 8062Valve Spring Compressor5110J 8087Cylinder Bore Gag

Illustration Tool Number/ Description5118J 33049Camshaft BearingService Set350498J 35621-BRear Main Seal Installer3413J 36660-AElectronic TorqueAngle

CCamshaft and Bearings Cleaning andInspectionEngine Mechanical - 5.0L and 5.7L ... 6-67Camshaft Bearing InstallationEngine Mechanical - 5

OOil Filter Adapter InstallationEngine Mechanical - 5.0L and 5.7L ... 6-121Oil Filter Adapter RemovalEngine Mechanical - 5.0L and 5.7L ...

Sealers, Adhesives, and LubricantsApplication Type of MaterialGM Part NumberUnited States CanadaCamshaft Retainer Bolt Threadlock 12345382 10953489Cra

TP-6104 11/01a

Component LocatorDisassembled ViewsSIE-ID = 348556Legend(1) Fuel Pipe Retainer Bracket(2) Fuel Pipe Retainer Bracket Nuts(3) Fuel Pipe(4) Fuel Pipe At

(22) Engine Coolant Thermostat(23) Water Outlet(24) Water Outlet Stud(25) Upper Intake Manifold Stud(26) Throttle Body Gasket(27) Throttle Body(28) Th

Legend(1) Engine Front Cover(2) Camshaft Timing Chain(3) Camshaft Sprocket(4) Camshaft Sprocket Bolt(5) Valve Lifter Guide Retainer Bolt(6) Valve Lift

CAUTIONCaution: In order to reduce the chance of personal injury and/or property damage, carefully observe the instructionsthat follow.The service man

Legend(1) Valve Rocker Arm Cover Bolt(2) Valve Rocker Arm Cover Bolt Washer(3) Valve Rocker Arm Cover(4) Valve Rocker Arm Cover Gasket(5) Valve Stem K

Legend(1) Piston Ring Kit(2) Piston(3) Connecting Rod(4) Connecting Rod Bolt(5) Connecting Rod Bearings(6) Connecting Rod Cap(7) Hex Nut (Connecting R

(32) Crankshaft Sprocket(33) Crankshaft Position Sensor Reluctor Ring(34) Woodruff Keys (Crankshaft Balancer)(35) Crankshaft Bearing(36) Crankshaft Be

Legend(1) Engine Block(2) Oil Pump Driveshaft(3) Oil Pump Driveshaft Retainer(4) Pin (Oil Pump Locator)(5) Oil Pump(6) Oil Pan Gasket(7) Oil Pan(8) Oi

Engine IdentificationSIE-ID = 650058The Vehicle Identification Number (VIN) is located onthe left side rear of the engine block, near thetransmission be

Repair InstructionsDraining Fluids and Oil Filter RemovalSIE-ID = 1945721. Remove the oil pan drain plug and allow theengine oil to drain into a suita

3. Remove the engine block coolant drain hole plugand allow the coolant to drain into a suitablecontainer.4. Remove the knock sensor and allow the coo

Exhaust Manifold Removal - LeftSIE-ID = 650059Notice:SIO-ID = 2878 Twist the spark plug bootone-half turn in order to release the boot. Pull on thespa

3. Remove the exhaust manifold bolts.4. Remove the spark plug wire shields.5. Remove the exhaust manifold.6. Remove and discard the exhaust manifold g

2. Remove the clamps and the water pumpinlet hose.3. Remove the water pump bolts.4. Remove the water pump.5. Remove the water pump gaskets.6. Discard

Table of ContentsTP-6104 11/01 Table of ContentsCaution Inside Front Cover...Introdu

2. Remove the bolts and the crankshaft pulley.Notice:Refer toFastener Noticein Cautions andNotices.3. Use theJ 23523-Fin order to remove thecrankshaft

Valve Rocker Arm Cover Removal - LeftSIE-ID = 6500611. Remove the valve rocker arm cover bolts andwashers.2. Remove the valve rocker arm cover.3. Remo

2. Remove the distributor clamp bolt.3. Remove the distributor and the distributor clamp.4. Remove the distributor gasket and discard.Intake Manifold

2. Remove the lower intake manifold bolts.Important: The intake manifold may be removed asan assembly. Do not remove the specific intakemanifold compon

Cylinder Head Removal - LeftSIE-ID = 6500641. Remove the engine coolant temperature gagesensor.2. Remove and discard the spark plugs.3. Remove the cyl

Notice:SIO-ID = 13838 After removal, place thecylinder head on two wood blocks to prevent damage.4. Remove the cylinder head.5. Remove and discard the

Cylinder Head Removal - RightSIE-ID = 6500651. Remove and discard the spark plugs.2. Remove the cylinder head bolts.Notice:SIO-ID = 13838 After remova

4. Remove and discard the cylinder head gasket.5. Remove the cylinder head locator dowel pin, ifrequired.Valve Lifter RemovalSIE-ID = 24119Tools Requi

Important: Place the valve lifters in the rack in theupright position in order to maintain the oil inside thevalve lifter.2. Remove the valve lifter g

Oil Pan RemovalSIE-ID = 668361. Remove the oil pan bolts and nuts.2. Remove the oil pan reinforcements.3. Remove the oil pan.4. Remove and discard the

Table of Contents, continuedTP-6104 11/01Table of ContentsCylinder Head Cleaning and Inspection 6-76...Val

Oil Pump, Pump Screen and DeflectorRemovalSIE-ID = 1953871. Remove the nuts (6) and the crankshaft oildeflector (2).2. Remove the oil pump bolt (1).3. R

Important: Always install a NEW crankshaft positionsensor seal, O-ring, during assembly.3. Remove the crankshaft position sensor seal,O-ring.4. Discar

2. Check the camshaft timing chain free play.If the camshaft timing chain can be moved inexcess of 11 mm (0.43 in), replacement ofthe camshaft timing

7. Remove the crankshaft balancer woodruff keys, ifrequired.Camshaft RemovalSIE-ID = 690311. Remove the bolts and the camshaft retainer.Notice:SIO-ID

Piston, Connecting Rod, and BearingRemovalSIE-ID = 24200Tools Required•J 5239Connecting Rod Bolt Guide Set•J 24270Cylinder Bore Ridge ReamerCaution: R

4. Use theJ 5239in order to protect the crankshaftjournals and remove the connecting rod and thepiston out of the top of the engine block.Important: A

3. Remove the crankshaft rear oil seal housing nutand bolts.4. Remove the crankshaft rear oil seal housing.5. Remove the crankshaft rear oil seal hous

5. Remove the crankshaft bearings from thecrankshaft bearing caps.6. Remove the crankshaft bearings from theengine block.Engine Block Plug RemovalSIE-

2. Remove the S type pin, and the crankshaft rearoil seal housing, if required.3. Remove the expansion cup plug from thecamshaft rear bearing hole.4.

5. Remove the engine oil pressure sensor gagesensor fitting.6. Remove the engine block oil gallery plugs fromthe rear of the engine block and discard.7

TP-6104 11/01 iIntroductionIntroductionThis service manual provides the service technicianwith information to service the General MotorsPowertrain eng

8. Remove the engine block oil gallery plugs fromthe front of the engine block and discard.Insert a 3/8 x 26 inch rod into the rear oil galleryholes i

Engine Block Cleaning and InspectionSIE-ID = 784233Tools RequiredJ 8087Cylinder Bore GageCaution: Refer to Safety Glasses Caution inCautions and Notic

9. Measure the cylinder bores for taper andout-of-round.9.1. Depress the plunger on theJ 80877mm(0.275 in) or until theJ 8087enters thecylinder bore.9

• The finish marks should be free from imbeddedparticles or torn or folded metal.4. When finished, the reconditioned cylinder boresshould have less than

Piston and Connecting Rod DisassembleSIE-ID = 195087Tools RequiredJ 24086-CPiston Pin Remover/InstallerCaution: Refer to Safety Glasses Caution inCaut

Piston, Connecting Rod, and BearingsCleaning and InspectionSIE-ID = 784237Caution: Refer to Safety Glasses Caution inCautions and Notices.Important: M

7. Measure the piston ring-to-piston ring groove sideclearance.7.1. Insert the edge of the piston ring into thepiston ring groove.7.2. Roll the piston

11. Inspect the connecting rod for twisting.12. Inspect the connecting rod for damage to theconnecting rod bolt threads.13. Measure the piston compres

Important: When assembling the piston andconnecting rod, the mark on the top of the piston mustpoint to the front of the engine block. The left bankco

3. Space the compression piston ring end gaps120 degrees apart.4. Space the oil control piston ring end gaps aminimum of 90 degrees apart.Crankshaft a

TP-6104 11/01ii IntroductionNotes

5. Inspect the crankshaft for the following:• Crankshaft journals (1) should be smooth withno evidence of scoring or damage.• Deep grooves (2)• Scratc

8. Using wooden V-blocks, support the crankshaft onthe front and rear journals.9. Use theJ 7872in order to measure crankshaftjournal runout.Refer toEn

11. Inspect the crankshaft bearings for craters orpockets. Flattened sections on the crankshaftbearing halves also indicate fatigue.12. Inspect the cr

Measuring Crankshaft Bearing ClearancesNotice:SIO-ID = 5016 Do not shim, scrape, or filebearing inserts. Do not touch the bearing surface of theinsert

3. Install the bearings into the engine block.Notice:Refer toFastener Noticein Cautions andNotices.4. Install the bearing cap bolts and tighten tospec

4. Insert a piece of paper card stock onto thecrankshaft journal. Install the bearing half, bearingcap, and bolts. Refer toFastener TighteningSpecifica

8. Install the pivot arm assembly (1) onto theconnecting rod.9. Position the foot of the pivot arm assembly overthe large end of the connecting rod bo

12. Align the center of the base (1) with the screw (3)of the pivot arm assembly.13. Tighten the bolt (2) until snug.14. Align the link (1) of the piv

16. Insert the handle (1) to the pivot arm assembly.17. Select the adapter (2), as required, and install tothe swivel base (1).18. Tighten until snug.

21. Install the swivel base (1) to the oil pan rail of theengine block.22. Tighten until snug.23. Adjust the swivel base as required, and positionthe

TP-6104 11/01 ICautions and NoticesCautions and NoticesDefinition of Caution, Notice, andImportantThe diagnosis and repair procedures in the GMPowertr

25. Rotate the fine adjustment knobs, on the dialindicator end of the swivel base, to position the tipof the indicator in contact with the connecting r

Measuring Crankshaft Bearing Clearances –Plastic Gage Method1. Install the crankshaft bearings into theengine block.2. Install the crankshaft.3. Insta

4. Install the crankshaft bearings into the crankshaftbearing caps.5. Install the crankshaft bearing caps in the originalpositions, and the arrow on t

Measuring Connecting Rod Bearing SideClearance1. Insert a feeler gage between the connecting rodcaps and measure the connecting rod sideclearance. Ref

Engine Flywheel Cleaning and InspectionSIE-ID = 195065Caution: Refer to Safety Glasses Caution inCautions and Notices.1. Clean the engine flywheel (1 o

5. Inspect the engine flywheel, manual transmission,if equipped, for the following:• Pitted friction surface (1)• Scoring or grooves (2)• Rust or other

6. Inspect the engine camshaft for the following:• Worn, scored, or damaged bearing journals (1)• Worn engine camshaft lobes (2)• Damaged bolt hole th

Camshaft Bearing RemovalSIE-ID = 195130Tools RequiredJ 33049Camshaft Bearing Service Kit1. Select the cone (1), the handle (10), theexpanding driver (

3.14. Tighten theJ 33049expander assembly nutuntil snug.3.15. Push theJ 33049guide cone into thecamshaft front bearing in order to aligntheJ 33049.3.1

Caution: Refer to Safety Glasses Caution inCautions and Notices.Important: The camshaft bearing lubrication holesmust align with the oil gallery holes

TP-6104 11/01II Cautions and NoticesMoving Parts and Hot Surfaces CautionCaution: Avoid contact with moving parts and hotsurfaces while working around

Important: The camshaft bearing lubrication holesmust align with the oil gallery holes in the engine block.After installation of the camshaft bearings

3.19. Drive the camshaft inner bearing #2 into thecamshaft inner bearing bore #2.3.20. Loosen theJ 33049expander assembly nut.4. Carefully remove theJ

Valve Rocker Arm and Push RodsCleaning and InspectionSIE-ID = 195201Important: Parts that are to be reused must bemarked, sorted and organized for ass

Valve Lifters and Guides Cleaning andInspectionSIE-ID = 195248Caution: Refer to Safety Glasses Caution inCautions and Notices.Important: Components th

Cylinder Head DisassembleSIE-ID = 195340Tools RequiredJ 8062Valve Spring CompressorCaution:SIO-ID = 411464Compressed valve springshave high tension ag

3. Dry the components with compressed air.4. Use theJ 8089to clean the carbon from thecylinder head combustion chambers.Be careful not to scuff the co

7. Use theJ 9666in order to measure the valvespring.Replace the valve spring if the valve springtension is less than 338 N (76 lb) at 43.2 mm(1.70 in)

10. Measure the valve stem-to-guide clearance.Excessive valve stem-to-guide clearance maycause an excessive oil consumption and may alsocause a valve

2. Improper valve stem (1) to valve guide (2)clearance may cause excessive oil consumption.Caution: Refer to Safety Glasses Caution inCautions and Not

6. Inspect the valve contact surface for the following:• Undersized margin (1)• Pitted surface (2)• Burnt or eroded areas (3)• Acceptable edge (margin

Engine Mechanical - 5.0L and 5.7LSpecificationsSIE-ID = 784227Fastener Tightening SpecificationsApplicationSpecificationMetric EnglishAccelerator Control

3. Rotate the nut clockwise to remove the valverocker arm ball stud.Valve Rocker Arm Stud InstallationSIE-ID = 195354Tools Required•J 5715Reamer (0.07

Cylinder Head AssembleSIE-ID = 195342Tools Required•J 8062Valve Spring Compressor•J 42073Valve Stem Seal InstallerCaution: Refer to Safety Glasses Cau

6. Install the valve spring (3).7. Install the valve spring cap (2) onto the valvespring (3), over the valve stem.Caution:SIO-ID = 411464Compressed va

Oil Pump DisassembleSIE-ID = 1950491. Remove the oil pump driveshaft and oil pumpdriveshaft retainer.Important: Do not remove the oil pump screen from

4. Remove the oil pump cover.5. Remove the oil pump drive gear and the oil pumpdriven gear.6. Matchmark the gear teeth for assembly.Caution: Refer to

Oil Pump Cleaning and InspectionSIE-ID = 35473Caution: Refer to Safety Glasses Caution inCautions and Notices.1. Clean the oil pump components in clea

3. Apply clean engine oil GM P/N UnitedStates 12345610, GM P/N Canada 993193, orequivalent, to the oil pump drive gear, the oil pumpdriven gear, and t

8. Install the oil pump screen.8.1. If removed, replace the oil pump screen.The oil pump screen must have a goodpress fit into the oil pump body.8.2. M

• Damage to the bolt holes (4)• Restrictions to the ventilation system passagesOil Pan Cleaning and InspectionSIE-ID = 194998Caution: Refer to Safety

2. Remove the throttle body attaching studs.3. Remove the throttle body.4. Remove the throttle body to upper intake manifoldgasket.5. Discard the thro